Eng 简体

nRF9151 DK Development kit

Cellular IoT development kit for LTE-M, NB-IoT, GNSS and DECT NR+

The nRF9151 DK is an affordable, pre-certified single board development kit for evaluation and development on the nRF9151 System-in-Package (SiP) for LTE-M, NB-IoT, GNSS and DECT NR+. It has a dedicated LTE-M, NB-IoT and DECT NR+ antenna that supports a wide range of bands to operate globally. The nRF9151 DK has the same coverage as the nRF9151 SiP. LTE bands B1-B5, B8, B12, B13, B17-B20, B25, B26, B28, B65, B66 and B85 are supported.

An integrated patch antenna for GNSS is also included on the PCB, while SWF RF connectors are available for measuring the performance of the RF signals. Both antenna connectors also allow for the use of external antennas.

All GPIOs and interfaces are available via connectors. The kit is Arduino Uno Rev3 compatible, meaning it can easily interface with external device shields, such as the nRF7002 EK, which can be used for Wi-Fi locationing. User-programmable LEDs and buttons (4 each) are available for output and input. 

The nRF9151 DK has both a nano/4FF SIM card slot and an MFF2 SIM footprint, to support plug-in and soldered (e)SIMs. The kit is shipped with a SIM card that is pre-loaded with free data. It also supports the use of Software SIM, further reducing power consumption.

Programming and debugging are enabled through the on-board SEGGER J-Link, which also supports programming and debugging external targets.

The nRF9151 DK is supported by a full suite of development software, tools and resources, including the Nordic Developer Academy’s Cellular IoT Fundamentals course. 

The nRF9151 DK comes pre-flashed with our Serial LTE Modem application for interfacing through AT Commands. Getting started with other firmware samples is available in the Quick Start tool, found in nRF Connect for Desktop. 

 

PDF IconDownload nRF9151 DK product brief (PDF)

Ask us about this
Key features
  • Global LTE-M/NB-IoT antenna
  • GNSS antenna
  • Supports DECT NR+ 
  • Arduino Uno form factor
  • 4 LEDs user-programmable
  • 4 buttons user-programmable
  • SEGGER J-Link OB Debugger with debug out support
  • UART interface through VCOM port
  • USB connection for debug/programming and power
  • Bundled with SIM cards from Onomondo and Wireless Logic preloaded with free data
Documentation
Downloads

nRF9151 DK application and modem firmware

Selected version
nrf9151dk_mfw-2.0.4_sdk-3.2.1 [Latest Version]

Changelog:

nrf9151dk_mfw-2.0.4_sdk-3.2.1 [Latest Version]

Changelog:

  • Includes FW from nRF Connect SDK v3.2.1
  • Includes Modem Firmware v2.0.4

The following samples and applications are part of the package:

 

nrf9151dk_mfw-2.0.2_sdk-3.1.0

Changelog:

  • Includes FW from nRF Connect SDK v3.1.0
  • Includes Modem Firmware v2.0.2

The following samples and applications are part of the package:

 

nrf9151dk_mfw-2.0.2_sdk-3.0.0

Changelog:

  • Includes FW from nRF Connect SDK v3.0.0
  • Includes Modem Firmware v2.0.2

The following samples and applications are part of the package:

 

nrf9151dk_mfw-2.0.2_sdk-2.9.0

Changelog:

  • Includes FW from nRF Connect SDK v2.9.0
  • Includes Modem Firmware v2.0.2

The following samples and applications are part of the package:

 

nrf9151dk_mfw-2.0.2_sdk-2.8.0

Changelog:

  • Includes FW from nRF Connect SDK v2.8.0
  • Includes Modem Firmware v2.0.2

The following samples and applications are part of the package:

 

nrf9151dk_mfw-2.0.1_sdk-2.7.0

Changelog:

  • Includes FW from nRF Connect SDK 2.7.0
  • Includes Modem Firmware v2.0.1

The following samples and applications are part of the package:

 

 

nrf9151dk_mfw-2.0.1_sdk-2.6.1

First release for nRF9151 DK

Changelog:

  • Includes FW from nRF Connect SDK 2.6.1
  • Includes Modem Firmware v2.0.1

The following samples and applications are part of the package:

 

 

Hardware files

Selected version
1.0.0 Layout and BOM resources

Changelog:

1.0.0 Layout and BOM resources

Changelog:
  • Improved PMIC layout to lower EMI

0.9.0 Layout and BOM resources

  • First release for nRF9151 DK (PCA10171)

nRF91x1 SiP DECT nr+ firmware

For access please contact Nordic sales or support

DECT NR+ Firmware Binaries


The official DECT NR+ firmware binaries can be accessed by contacting Nordic Sales, check the changelogs for more information what the different version has introduced.

  • Changelog: MAC and PHY v2.0.0

     

    • This release introduces comprehensive DECT MAC (Medium Access Control) layer functionality, building upon the existing PHY layer capabilities.
      This release supports star network topology.

      This release supports: nRF9151 LACA A0/A1 SiP

      This firmware supports the "Release 2 of the DECT-2020 New Radio (NR) technical specification v2.1.1"

      DECT NR+ operation is enabled on frequency bands 1, 2, 3, 4*, 9 and 22. (*only on the nRF9151).

       

      Highlights:

      The MAC layer provides high-level network management, device association, and data communication services for DECT-2020 NR applications.

      • Network Management: Full star network topology support with network/cluster management, discovery, and RSSI scanning.
      • Device Communication: Association management with up to 6 concurrent flows, using RACH (uplink) and paging (downlink).
      • Data Link Control (DLC): Four service modes (Transparent, Segmentation, ARQ) with advanced flow control.
      • Advanced MAC Features: Link adaptation (MCS & power), HARQ, MAC-level security (Mode 1), IPv6 support, and configurable power saving (PT mode).
      • Operational Modes: Supports Fixed Termination (FT) parent and Portable Termination (PT) child roles.
      • Clock Synchronization: Clock synchronization to external 1PPS input and 1PPS output generation.

      A complete list of new functionality, changes and bug fixes is in the release notes found here or inside the .zip file.

      This release is aligned with v1.3 of the nRF91x1 DECT NR+ AT Commands Reference Guide.

      It is advisable to use the latest version of nRF Connect for Desktop and nRF Connect Programmer tools.

      Some features require support from the nRF Connect SDK, and it is recommended to ensure compatibility with the appropriate version of the SDK.
      Customers are encouraged to use NCS/main. The nRF Connect SDK release v3.3.x. will support the API fully.

       

  • Changelog: PHY only v2.0.0

     

    • This release includes PHY layer only.
      This release supports: nRF9151 LACA A0/A1 SiP

      This firmware supports the "Release 2 of the DECT-2020 New Radio (NR) technical specification v2.1.1"

      DECT NR+ operation is enabled on frequency bands 1, 2, 3, 4*, 9 and 22. (*only on the nRF9151).

      Highlights:

      • L1 Control: Refactored for improved maintainability.
      • Clock Synchronization: Added support for external 1PPS input and 1PPS output generation.
      • General Improvements: Includes various bug fixes and removal of unnecessary AT commands.

      A complete list of new functionality, changes and bug fixes is in the release notes found here or inside the .zip file.

      This release is aligned with v1.3 of the nRF91x1 DECT NR+ AT Commands Reference Guide.

      It is advisable to use the latest version of nRF Connect for Desktop and nRF Connect Programmer tools.

      Some features require support from the nRF Connect SDK, and it is recommended to ensure compatibility with the appropriate version of the SDK.
      Customers are encouraged to use NCS/main. The nRF Connect SDK release v3.3.x. will support the API fully.

       

  • Changelog: PHY only v1.1.0

     
    • • Enabling a 1-slot turnaround time for PHY operations in low-latency modes
    • • Added support for adding and removing scheduled operations
    • • Enhanced support for various radio modes to improve power consumption across different use cases.
    • • Added reporting of turnaround times for different radio modes.
    • • Introduced support for DECT NR+ band 4, available on the nRF9151 LACA A0 and nRF9151 LACA A1.
    • • Add support for 21 dBm output power on bands B1, B2, B9, and B22, available on the nRF9151 LACA A0 and A1.
        Note: Output power on Band 4 is limited to 19 dBm.
    • • Included battery voltage values in PHY operation callbacks.
    • • Added operation handle values for all PCC and PDC reception callbacks, simplifying packet identification for RX operations.